Bed Building Continued…

“Previously on BUILDING THE NEW VOME”…    Sounds kinda like the opening of a TV serial.

But seriously we started with building the frame and then started putting on the top.  I gave you a few tips on “how-did” construction ideas.  I try not to use the “how-to” phrase because I’m not expert enough to give “how-to” advice.  Instead, I will share how I did it and the reasoning behind why.  Sometimes that is based on some research and sometimes just plain old experience.

I’ve attached the rear two top pieces and will put the hinges on the front two pieces.  I refer to these as two pieces, because of the shape of the van and the window trim one long piece would no go down into place. (Refer to the first bed building post, I told ya so.  Sometimes it’s just easier to build in place since there’s very few things that are straight and square in a van.)   Besides, it’s part of my plan to hinge one half of the front of the bed.

A view of the two halves of the bed. Rear half is covered  and fixed. Front half is ready for hinges.
A view of the two halves of the bed. Rear half is covered and fixed. Front half is ready for hinges.

If you look under the bed you will see a dividing wall in place.  This is so that the stuff in the back stays in the back while I’m driving.  Here’s a little better view of that divider from the rear of the bed.

View of the divider wall from the rear side.
View of the divider wall from the rear side.

I made the front half hinged to swing open on the top.  The left side has a pop-off panel held on by magnetic latches to access a pull out drawer.  Since the right half of the bed is where I will put the batteries and the inverter that front is fixed in place.

Front half after hinges installed.  Also notice the divider wall underneath.
Front half after hinges installed. Also notice the divider wall underneath.

To answer a question Julie asked, I used piano hinges from my local Lowe’s store to hinge the tops.  And as you can see a simple “prop stick” to hold them open.  I considered getting some gas struts from a junkyard, but decided simple would be best.

If you look closely at the picture above on the left side of the lid it has been trimmed down.  This trimming was to allow the lid to clear the trim around the windows and allow the lid to swing into a near vertical position.  Remember angles in a van are seldom square?

This is the finished bed with the slide out drawer being built in front of it.  I chose to make the drawer be just a lift up and tug out affair.  I could have built rails in the space and then added drawer slides.  But again I chose simple. the added benefit is when it is slid back into place it’s resting behind a frame member across the bottom and not sliding out.

IMAG1471That pretty much finishes the bed.  I will put a coat of clear varnish on the front to protect it and make it easier to keep clean.  And may add some aluminum angle as trim on the front edge of the lid to prevent splintering and give it a better appearance.

Oh yeah, the  pad is the two pieces of orthopedic foam from the two twin beds that were there.  I added a full sized topper pad to cover where the two pieces meet.   Now this bed actually sleeps better than the one in the house.

Next some odds and ends pieces to be installed.   So until next time…

“Get Out, Be Safe, and Go Adventure.”

3 thoughts on “Bed Building Continued…”

  1. I too am interested in the window ‘perf’. What is it? How is it applied? Cost? What are the benefits? Thanks!

    1. It is a product used by sign and graphics companies to put advertising on vehicles.
      I chose to let someone with a lot more practice than I put it on. It only took about two and
      half hours to put it on. For the average van it should cost around $350, that’s 47 sq. feet of window.
      Increased privacy during the daytime without that “cave” feeling. And in my case it covered on the outside
      The factory limo-tint glass with a white surface to reflect sunlight instead of absorbing it and radiating heat to the interior.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

Travels and tips for being off-grid

dan cordray and brenda durbin

Travels and tips for being off-grid

Through Open Lens

Home of Lukas Kondraciuk Photography

Forest Edge Studio

Artist's Journal - C. Gemme Messier

TRAVELLING THE WORLD SOLO

The ultimate guide for independent travellers seeking inspiration, advice and adventures beyond their wildest dreams

%d bloggers like this: